Conversation
jmorris

James Morris

Working on a 10 GHz power amp. #hamradio #amateurradio #electronics #microwave
2
0
10
jtfletchbot@mastodon.hams.social

Josh KD2YGL

Reply to @jmorris

@jmorris What's the input and output wattage? If you don't mind my asking.

1
0
0
jmorris

James Morris

Reply to @jtfletchbot@mastodon.hams.social
@jtfletchbot this is for a TGA2623-CP device (yet to arrive), with the aim of 25W out for about 60mW in.
2
0
0
jmorris

James Morris

Reply to @jmorris
Edited 9 months ago
@jtfletchbot I believe it can produce more linear power with higher voltage and aggressive cooling, but 25W will be a good start.
0
0
0
jmorris

James Morris

Reply to @jmorris
@jtfletchbot btw, the PCB and housing is from Lothar Baier, https://texasmicrowave.com/ . Saves a mountain of busywork for me.
1
0
0
jtfletchbot@mastodon.hams.social

Josh KD2YGL

Reply to @jmorris

@jmorris That's very cool! I wish you luck in your endeavors!

0
0
1
jmorris

James Morris

Reply to @jmorris
Load testing the bias power supply. The amp uses an expensive ($650) GaN transistor which must have bias applied before main power, or it will be destroyed - it’s ‘on’ by default and needs bias to switch ‘off’. I’m being extra careful with this, will also verify the power up sequence on a scope, response to short circuit etc.
1
0
1
jmorris

James Morris

Reply to @jmorris
Edited 9 months ago
Here's a trace of the power up sequence, with the gate voltage at the top, and drain at the bottom. I'm not sure if the CRO is fast enough to catch the sequence correctly, because I can't tell if there's a gap between gate & drain. IIUC, the negative regulator chip provides a 'voltage ok' signal that is used to switch the gate, so it should be ok. But, I'll keep investigating until I'm sure.

This is the kind of thing that leads to long development times for amateur microwave radio projects, so many (fascinating) rabbit holes and a lot of learning as you go. I wonder if more people knew about this aspect of the hobby, whether we'd see more and younger people joining.
1
1
1
n8dmt@mastodon.radio

Gary @N8DMT

Reply to @jmorris

@jmorris Analog Devices makes voltage sequencers for turn on and turn off control. Digikey has an overview article to help designers get started. Have found turn-off to be a bigger challenge than turn-on…

0
0
1
About social.kernel.org

Terms of service

  1. Please do not use this service in violation of the Linux Kernel Code of Conduct. Doing so will result in your account suspension with the referral of the matter to the CoC committee.

  2. "Repeating"/"boosting" someone else's status on this platform will be treated as endorsement and will fall under rule #1.

  3. You are encouraged to use this platform to promote your work on the Linux Kernel, but there is no restriction on permitted topics (with the exception of anything covered by #1 above).

  4. There is no requirement to post in English, but it should be considered the primary language of communication on this platform.

Privacy notice

The admins of this service have access to all posted statuses. They aren't looking, but if it's something they shouldn't know about, then you should not post it on this platform.

Please see the Linux Foundation Privacy Policy, which applies to this platform as well.

Getting your own account

If you would like an account on this instance, please check that the following applies to you:

  • You are listed in MAINTAINERS or CREDITS

  • OR: You have a kernel.org account or email address

  • OR: You have a long and established history of involvement with the Linux Kernel

If the above is true and you agree with the Terms of Service and Privacy Notice listed above, please use these instructions to request an account: